Hammerite Direct To Rust Metal Paint Aerosol Smooth Finish , (2-in-1) Paint & primer, Fence, Furniture, Smooth finish, 0.4 L, ...

Hammerite Direct To Rust Metal Paint Aerosol Smooth Finish 0.4 L

From £11.42
Offres:

Product Information

Hammerite Direct To Rust Metal Paint Aerosol Smooth Finish . Product type: (2-in-1) Paint & primer, Best uses: Fence, Furniture, Finish type: Smooth finish. Package width: 64 mm, Package depth: 64 mm, Package height: 199 mm. Quantity per pack: 1 pc(s). Suitable for materials: Metal. Master (outer) case width: 200 mm, Master (outer) case length: 136 mm, Master (outer) case height: 200 mm

House Paints Hammerite
Product
Name
Hammerite Direct To Rust Metal Paint Aerosol Smooth Finish 0.4 L
Category
House Paints
Brand
Hammerite
Features
Product type
(2-in-1) Paint & primer
Suitable for outdoor use
Yes
Suitable for indoor use
No
Best uses
Fence, Furniture
Finish type
Smooth finish
Paint volume
0.4 L
Colour name
Dark Green
Composition
Solvent-based
Volatile organic compounds (VOC) content
399 g/l
Volatile organic compounds (VOC) content labelling system
Very high (>50%)
Coverage per pack
0.5 m²
Minimum drying time
1 h
Maximum drying time
2 h
Recoat after
0.25 h
Number of coats (min)
3
Number of coats (max)
4
Rust protection
Yes
Dispenser type
Spray
Protection term
8 year(s)
Surface preparation
Abrade smooth surfaces and remove all loose and flaking paint with a wire brush. Remove dirt and dust with diluted detergent. Remove grease with Hammerite Brush Cleaner & Thinners. Then rinse with clean water and allow time to dry. Spray a test patch of Hammerite Direct to Rust Metal Paint onto painted surfaces and leave for at least 1 hour. If there is no reaction apply Hammerite Direct to Rust Metal Paint directly to surface. If there is a reaction remove all paint from the surface.On bare zinc, aluminium and galvanised surfaces, apply Hammerite Special Metals Primer before applying Hammerite Direct to Rust Metal Paint
How to use
Store aerosol at room temperature for 2 hours prior to use. Shake can vigorously, in a vertical motion, until the agitator ball is heard and then for a further 3 minutes.Apply light even coats, from a distance of approximately 15cm (6 inches) and keep the aerosol moving. Do NOT concentrate spray in one spot. Apply 3-4 coats for maximum protection and allow 15 minutes between coats. Between coats invert can and spray for 2 seconds to avoid blockages
HSE note
Flame, Exclamation mark Danger. Contains HYDROCARBONS, C6-C7, N-ALKANES, ISOALKANES, CYCLICS,less than 5% N-HEXANE. Extremely flammable aerosol. Causes skin irritation. May cause drowsiness or dizziness. Harmful to aquatic life with long lasting effects. Pressurized container: may burst if heated. Keep out of reach of children. If medical advice is needed, have product container or label at hand. Wear protective gloves. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Do not get in eyes, on skin, or on clothing. Do not pierce or burn, even after use. IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER or doctor if you feel unwell. Protect from sunlight. Do not expose to temperatures exceeding 50 degrees C/122 degrees F. Dispose of contents and container in accordance with all local, regional, national or international regulations. Contains 2-butanone oxime. May produce an allergic reaction
Packaging content
Quantity per pack
1 pc(s)
Packaging data
Package width
64 mm
Package depth
64 mm
Package height
199 mm
Package weight
470 g
Logistics data
Master (outer) case width
200 mm
Master (outer) case length
136 mm
Master (outer) case height
200 mm
Products per master (outer) case
6 pc(s)
Layers per pallet
4 pc(s)
Products per pallet layer
222 pc(s)
Products per pallet
888 pc(s)
Other features
Suitable for materials
Metal
NOTE: The above information is provided for your convenience only, and we cannot guarantee its accuracy with the seller.

Customer Reviews

Share your opinion on the product or read reviews from other members.